P1546, P2094 thru P2100 - 2 Hole, Outside Angle Fitting (1-5/8" Series)

P1546-No-Dimensions.png
Part No. A B C Finish Product Weight / Piece (lbs)
P1546 45° 3" (76) 2-5/16" (59) EG 0.58
P1546 45° 3" (76) 2-5/16" (59) DF 0.615
P1546 45° 3" (76) 2-5/16" (59) HG 0.615
P1546 45° 3" (76) 2-5/16" (59) GR 0.58
P1546 45° 3" (76) 2-5/16" (59) ZD 0.58
P1546 45° 3" (76) 2-5/16" (59) SS 0.58
P1546 45° 3" (76) 2-5/16" (59) AL 0.23
P2094 82-1/2° 3-9/16" (91) 1-11/16" (43) EG 0.58
P2094 82-1/2° 3-9/16" (91) 1-11/16" (43) HG 0.615
P2094 82-1/2° 3-9/16" (91) 1-11/16" (43) GR 0.58
P2094 82-1/2° 3-9/16" (91) 1-11/16" (43) ZD 0.58
P2095 75° 3-9/16" (91) 1-11/16" (43) EG 0.58
P2095 75° 3-9/16" (91) 1-11/16" (43) HG 0.615
P2095 75° 3-9/16" (91) 1-11/16" (43) GR 0.58
P2096 67-1/2° 3-1/2" (89) 1-3/4" (45) EG 0.58
P2096 67-1/2° 3-1/2" (89) 1-3/4" (45) HG 0.615
P2096 67-1/2° 3-1/2" (89) 1-3/4" (45) GR 0.58
P2096 67-1/2° 3-1/2" (89) 1-3/4" (45) ZD 0.58
P2097 60° 3-3/8" (86) 1-7/8" (48) EG 0.58
P2097 60° 3-3/8" (86) 1-7/8" (48) HG 0.615
P2097 60° 3-3/8" (86) 1-7/8" (48) GR 0.58
P2097 60° 3-3/8" (86) 1-7/8" (48) ZD 0.58
P2097 60° 3-3/8" (86) 1-7/8" (48) SS 0.58
P2098 52-1/2° 3-1/4" (83) 2-1/16" (52) EG 0.58
P2098 52-1/2° 3-1/4" (83) 2-1/16" (52) HG 0.615
P2098 52-1/2° 3-1/4" (83) 2/1/16" (52) GR 0.58
P2098 52-1/2° 3-1/4" (83) 2/1/16" (52) ZD 0.58
P2099 37-1/2° 3-1/2" (89) 1-13/16" (46) EG 0.58
P2099 37-1/2° 3-1/2" (89) 1-13/16" (46) HG 0.615
P2099 37-1/2° 3-1/2" (89) 1-13/16" (46) GR 0.58
P2099 37-1/2° 3-1/2" (89) 1-13/16" (46) ZD 0.58
P2099 37-1/2° 3-1/2" (89) 1-13/16" (46) AL 0.23
P2100 37-1/2° 2-11/16" (68) 2-5/8" (67) EG 0.58
P2100 37-1/2° 2-11/16" (68) 2-5/8" (67) HG 0.615
P2100 37-1/2° 2-11/16" (68) 2-5/8" (67) GR 0.58
P2100 37-1/2° 2-11/16" (68) 2-5/8" (67) ZD 0.58

    Design Loads
    Design Loads - P1546, P2094 thru P2100
    Part Number Angle  Average Ultimate Tension
    (lbs)    		  Design Tension Load
    (lbs)    		 Average Deflection at Design Tension Load
    P2094 82-1/2° 7,000 1,500 0.046"
    P2095 75° 7,200 1,500 0.081"
    P2096 67-1/2° 6,900 1,500 0.046"
    P2097 60° 6,500 1,500 0.079"
    P2098 52-1/2° 6,300 1,500 0.059"
    P1546 45° 6,200 1,500 0.081"
    P2099 37-1/2° 6,800 1,500 0.171"
    P2100
    		 37-1/2° 5,700 1,500 0.169"
     
    Notes:
    1. Design loads only apply to UNISTRUT brand products. Look for "UNISTRUT" on the part.
    2. Average Safety Factor = 4.0 based on static testing to the ultimate strength of connection. Design Loads are limited to 1,500 lbs for Slip Load of Channel Nuts with a Safety Factor = 3.0.
    3. 1/2" Unistrut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    4. Deflection is the average of straight line interpolations of deflection readings at 1,000 lbs and 2,000 lbs Tension Loads. Deflection is measured in the direction of the Tension Load.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Unistrut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1 or SC3
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.

    Related Resources

    Videos

    Technical Documents