P1386 - Beam Clamp

P1386-No-Dimensions.png
Part No. Finish Product Weight / Piece (lbs)
P1386 EG 0.27
P1386 DF 0.286
P1386 HG 0.286
P1386 GR 0.27
P1386 SS 0.27

    Design Loads

    Design Loads - P1386
    ChannelStyle Design Load Each
    (Use in Piars Only)
    lbs (kN)
    P1000 600  (2.67)
    P1100 500  (2.22)
    P2000 450  (2.00)

    Notes:

    1. Design loads only apply to Unistrut brand products. Look for "UNISTRUT" on the part.
    2. Use in pairs only.
    3. Safety factor = 5 based on ultimate strength of connection.
    4. Requires a P1010 Channel Nut and 1/2" bolt.
    5. Set Screw Installation Torque: 125 in-lbs (14 N-m)

    Seismic Design Loads
    P1386 Allowable (Design) Loads
    (lbs)
    Pullout Slip Along Slip Thru
    1,200 200 600

    Notes:
    1. Design loads only apply to UNISTRUT brand products. Look for "UNISTRUT" on the part.
    2. Seismic design loads are for the 2 clamp installation as shown above. Must use clamps in pairs.
    3. Design loads are based on static testing with a safety factor = 5 based on ultimate strength of connection.
    4. Design loads apply only when used with 12ga. UNISTRUT channel.
    5. A 1/2" Chanel Nut and Bolt are required for installation.
    6. Set Screw Installation Torque: 125 in-lbs (14 N-m)

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Unistrut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1 or SC3
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.